flexiblefullpage
billboard
interstitial1
catfish1
Currently Reading

Modest growth predicted for engineering, construction mergers

Modest growth predicted for engineering, construction mergers

Small and mid-market deals and construction materials drive activity; U.S. is the most active individual nation.


By Posted by Julie S. Higginbotham, Senior Editor | February 8, 2013
Mergers and acquisitions in the construction industry picked up steam in late 20
Mergers and acquisitions in the construction industry picked up steam in late 2012.

 

Though overall 2012 merger and acquisition (M&A) activity in the engineering and construction industry did not meet levels seen in 2011, an uptick in fourth quarter activity points to signs of recovery, according to Engineering Growth, a quarterly analysis of the global engineering and construction industry by consultant PwC US.

“With the continued elevated level of uncertainty through the end of the year, we saw many deal makers staying on the sidelines or engaging in smaller, bolt-on acquisitions. However, as the global engineering and construction sector continues on its path of slow recovery, we remain cautiously optimistic and expect the M&A arena to follow a similar trajectory of modest growth in 2013. Growing infrastructure needs, expanding urbanization, and the need for cleaner, environmentally friendly and sustainable energy and water continue to be the driving forces of M&A activity in the sector,” said H. Kent Goetjen, U.S. engineering and construction leader with PwC.

In 2012, there were 168 deals (with values of $50 million or more) totaling $49.3 billion, compared with 181 transactions worth $73.3 billion in 2011. Overall 2012 M&A volume and value declined compared with 2011 levels, but the sector did see increased activity in the fourth quarter of 2012: 57 deals totaling $13.9 billion, an increase in value and volume compared with the third quarter of 2012 (31 transactions totaling $10.8 billion). 

Despite the slowdown in engineering and construction dealmaking, financial investors continue to slowly gain momentum. In 2012, the participation of financial advisors was higher than the average 10-year rate of about 33 percent of financial acquirers and they were an active participant in some of the largest deals during the year, potentially suggesting signs of recovery and opportunity in the sector. 

Transactions in the construction materials category led deals in the full year of 2012 in both value and volume with 46 deals over $50 million totaling $16.57 billion, outnumbering the construction segment, the usual leader and second in terms of volume in 2012. Multiple large and mega deals throughout 2012, including the only mega-deal in the fourth quarter, involved targets associated with the construction materials segment (notably, cement and concrete), contributing to a 70% increase in value in the segment’s deals over 2011.

The majority of engineering and construction transactions in 2012 were local deals, for both U.S. targets and targets and acquirers from other parts of the world. Asia and Oceania remained the most active region in engineering and construction dealmaking, representing 68 deals totaling $15.09 billion in 2012, followed by Europe and North America. The United States was the most active individual nation, engaging in the largest number of deals and also tending to generate higher deal values due to the relative maturity, size, and financial stability of U.S.-affiliated dealmakers. 

For a copy of Engineering Growth, visit: www.pwc.com/us/industrialproducts

Related Stories

Sponsored | | Nov 19, 2014

Long-life coatings vs. long-life screws

Are you concerned with the long-life protection of your metal building project? SPONSORED CONTENT

Sponsored | | Nov 19, 2014

Build green while you work green

Leading general contractors, including Skanska USA and Turner Construction, are implementing sustainable modular jobsite offices throughout the country. SPONSORED CONTENT

Sponsored | | Nov 19, 2014

Fire resistive, blast-resistant glazing: Where security, safety, and transparency converge

Security, safety and transparency don’t have to be mutually exclusive thanks to new glazing technology designed to support blast and fire-resistant secure buildings. SPONSORED CONTENT

| Nov 19, 2014

Must see: Arup, Damian Rogers propose urban surf park in Melbourne

The surfing pool would offer 98-foot-wide waves that would run the length of the 500-foot-long enclave.

| Nov 18, 2014

Architecture Billings Index dips in October, still shows positive outlook design services

Headed by the continued strength in the multifamily residential market and the emerging growth for institutional projects, demand for design services continues to be healthy, as exhibited in the latest Architecture Billings Index.

| Nov 18, 2014

New tool helps developers, contractors identify geographic risk for construction

The new interactive tool from Aon Risk Solutions provides real-time updates pertaining to the risk climate of municipalities across the U.S.

| Nov 18, 2014

Grimshaw releases newest designs for world’s largest airport

The airport is expected to serve 90 million passengers a year on the opening of the first phase, and more than 150 million annually after project completion in 2018. 

| Nov 17, 2014

Nearly two years after Sandy Hook, the bloodshed continues

It’s been almost two years since 20 first-graders were shot and killed at Sandy Hook Elementary School in Newtown, Conn., but these incidents, both planned and random, keep occurring, writes BD+C's Robert Cassidy.

| Nov 17, 2014

Hospitality at the workplace: 5 ways hotels are transforming the office

During the past five years, the worlds of hospitality and corporate real estate have undergone an incredible transformation. The traditional approach toward real estate asset management has shifted to a focus on offerings that accommodate mobility, changing demographics, and technology, writes HOK's Eva Garza.

| Nov 17, 2014

Developments in 3D printing can assist architecture in the smallest details

Researchers at the Department of Energy’s Oak Ridge National Laboratory (ORNL) have developed a way for 3D printed metals to be produced with an unprecedented degree of precision.

boombox1
boombox2
native1

More In Category




halfpage1

Most Popular Content

  1. 2021 Giants 400 Report
  2. Top 150 Architecture Firms for 2019
  3. 13 projects that represent the future of affordable housing
  4. Sagrada Familia completion date pushed back due to coronavirus
  5. Top 160 Architecture Firms 2021